Arduino MCP2515 CAN Bus Interface Tutorial | Buzzza.com

Arduino MCP2515 CAN Bus Interface Tutorial


Click Here And Get This Posted To YOU In PDF Format

In this project, we will learn about the MCP2515 CAN Controller Module, how to interface the MCP2515 CAN Bus Controller with Arduino and finally how to enable communication between two Arduino board with the help of two MCP2515 CAN Controllers and the CAN Protocol.

Arduino MCP2515 CAN Bus Interface Image

Introduction

Controlled Area Network of simple CAN is a bus standard that allows a Microcontroller and its peripheral devices to communicate without the need of a host device or a computer.

Developed by Robert Bosch GmbH, CAN is protocol is main used in automobiles for communication between a control unit and its components.

For example, the Engine Control Unit is a major control using in a car. This unit is connected to many sensors and actuators like air flow, pressure, temperature, valve control, motors for air control etc. The communication between these modules and the control unit is through CAN Bus.

In order to understand a little bit more about CAN Bus, CAN Controller and other important aspects, the MCP2515 CAN Bus Controller Module is very helpful.   

Also read: BASICS OF SPI COMMUNICATION.

A Brief Note on MCP2515 CAN Bus Controller Module

The MCP2515 CAN Bus Controller is a simple Module that supports CAN Protocol version 2.0B and can be used for communication at 1Mbps. In order to setup a complete communication system, you will need two CAN Bus Module.

The module used in the project is shown in the image below.

Arduino MCP2515 CAN Bus Interface MCP2515 CAN Module

This particular module is based on MCP2515 CAN Controller IC and TJA1050 CAN Transceiver IC. The MCP2515 IC is a standalone CAN Controller and has integrated SPI Interface for communication with microcontrollers.

Coming to the TJA1050 IC, it acts as an interface between the MCP2515 CAN Controller IC and the Physical CAN Bus.

The following image shows the components and pins on a typical MCP2515 Module.

Arduino MCP2515 CAN Bus Interface MCP2515 CAN Module Components

Schematic of MCP2515 CAN Bus Module

Before seeing the schematic of the module, you need to understand a couple of things about both the ICs i.e. MCP2515 and TJA1050.

MCP2515 IC is the main controller that internally consists of three main subcomponents: The CAN Module, the Control Logic and the SPI Block.

CAN Module is responsible for transmitting and receiving messages on the CAN Bus. Control Logic handles the setup and operation of the MCP2515 by interfacing all the blocks. The SPI Block is responsible for the SPI Communication interface.

Coming to the TJA1050 IC, since it acts as an interface between MCP2515 CAN Controller and the physical CAN Bus, this IC is responsible for taking the data from the controller and relaying it on to the bus.

The following image shows the schematic of the MCP2515 CAN Module and it shows how MCP2515 IC and TJA1050 IC are connected on the Module.

Arduino MCP2515 CAN Bus Interface MCP2515 Schematic

Circuit Diagram for Interfacing MCP2515 with Arduino

The following image shows the circuit diagram of interfacing MCP2515 CAN Module with Arduino and possible communication between two Arduino over CAN Protocol.

Arduino MCP2515 CAN Bus Interface Circuit Diagram

If the pins of the MCP2515 Module are not clear, the following image might be useful.

Arduino MCP2515 CAN Bus Interface MCP2515 CAN Module Pins

Components Required

Arduino UNO x 2
MCP2515 x 2
USB Cable x 2
Connecting Wires

Circuit Design

As mentioned earlier, the CAN Controller IC facilitates SPI Communication Protocol for interfacing with any Microcontroller. Hence, connect the SPI Pin i.e. SCK, MOSI (SI), MISO (SO) and CS of the MCP2515 Module to corresponding SPI Pins of Arduino (see circuit diagram).

Arduino MCP2515 CAN Bus Interface Circuit Design

Make two such connections: one pair acts as a transmitter and the other as a receiver. Now for the communication between this transmitter and receiver, connect CANH and CANL pins of each MCP2515 Module.  

Code

Before going into the code, you need to download a library for the MCP2515 Module. There are many libraries but I have used this particular one.

Download it and place the extracted contents in the libraries directory of Arduino.

Since the communication involves a Transmitter Module and a Receiver Module, the code is also divided into Transmitter Code and Receiver Code.

Transmitter Code

Receiver Code

Working

Working of this project is very simple as all the work is done by the libraries (SPI and CAN). Since CAN is message-based communication, you need to send a message anywhere between 0 and 8 bytes.

In this project, the transmitter is sending a message as 1 1 2 3 0 5 6 7. This message is transmitted over CAN Bus and the receiver receives this message and is displayed on its serial monitor.

Additionally, the 0th and 4th bit i.e. 1 and 0 in the above sequence are extracted separately by the receiver and turns ON and OFF the LED connected to Pin 2 of Arduino.

Applications

As mentioned in the introduction, CAN is widely used in the field of automobiles. Some of the applications include:

Electronic Gear Shift System
Main Interface in Automation (like industrial)
Medical Equipment
Robotics
Auto Start/Stop of Car Engine

The post Arduino MCP2515 CAN Bus Interface Tutorial appeared first on Electronics Hub.

Read more: electronicshub.org

What's Your Reaction?

Cry Cry
0
Cry
Cute Cute
0
Cute
Damn Damn
0
Damn
Dislike Dislike
0
Dislike
Like Like
0
Like
Lol Lol
0
Lol
Love Love
0
Love
Win Win
0
Win
WTF WTF
0
WTF

Comments 0

Your email address will not be published. Required fields are marked *

Arduino MCP2515 CAN Bus Interface Tutorial

log in

Become a part of our community!

Captcha!
Don't have an account?
sign up

reset password

Back to
log in

sign up

Join BoomBox Community

Captcha!
Back to
log in
Choose A Format
Personality quiz
Trivia quiz
Poll
Story
List
Open List
Ranked List
Meme
Video
Audio
Image