How to Fix a Leaking Bathtub Faucet | Buzzza.com

How to Fix a Leaking Bathtub Faucet


Click Here And Get This Posted To YOU In PDF Format

Bathtub Faucet Repair Step 1: Make sure you have new parts available

The first step for bathtub faucet repair is learning how to fix a leaky bathtub faucet is to make sure you have the new parts that you need. You can fix most bathtub plumbing problems with the replacement parts available at hardware stores and home centers. A plumbing parts distributor will carry a much larger selection and may be able to special-order hard-to-find items (look under “ Plumbing Parts and Supplies” in your local Yellow Pages or online). There are thousands of different faucet replacement parts available to fix a leaky bathtub faucet, so bring your old parts to the store for a proper match to fix a leaky bathtub faucet. If your valve is highly corroded or the finish is wearing off, replace the entire faucet.

Step 2: Disassemble the faucet
How to Fix a Leaking Bathtub Faucet

Photo 1: Pry off the handle insert

Shut off the water supply to the faucet and open the valves to drain excess water from the system. Pry off the handle insert with the thin blade of a pocketknife. How to Fix a Leaking Bathtub Faucet

Photo 2: Remove the handle screw

Remove the handle screw. Then wiggle the handle and pull it off. If the handle doesn’t come off, heat it with a hair dryer to free it. Be careful; if you pull too hard, it’ll break. how to fix a leaky bathtub faucet

Photo 3: Pop loose the handle

Turn the handle screw about halfway back into the stem. Position the handle puller’s post against the screwhead and press the arms together behind the handle. Turn the post clockwise until the handle pops loose. Remove the handle screw and handle. Then pull off or unscrew the escutcheon plate. how to fix a leaky bathtub faucet

Photo 4: Remove the stem

Slide the bath socket onto the stem bonnet and turn it counterclockwise to break the stem loose. If it sticks, soak it with penetrating lubricant. Unscrew and remove the stem. how to fix a leaky bathtub faucet

Photo 5: Use a seat wrench

Press the seat wrench firmly into the center of the seat. Turn counterclockwise to snap the seat loose and remove it. If it sticks, soak it with penetrating lubricant. Coat the threads of the new seat with pipe dope and screw it into the fixture body with the seat wrench.

Removing the faucet handle is the toughest part of the job. Over time, corrosion can virtually weld the handle to the stem. Remove the handle by following the instructions in Photos 1 and 2. If the handle won’t come off, don’t force it-it might break. Instead, remove it with a special handle puller (Photo 3). Once the handles off, unscrew the escutcheon and stem assembly (Photo 4 and Fig. A). The stem assembly controls the amount and temperature of the water dispensed through the tub spout or shower head. Remove it with a special bath socket wrench, which looks like a spark plug wrench on steroids (Photo 4).

Leaks usually occur for two reasons. Over time, the seat washer stiffens and won’t seal tightly. And water pressure gradually erodes the brass rim of the seat (Photo 5). Replace the seat using a special seat wrench as shown in Photo 5.

Step 3: Replace the faucet stem parts
How to Fix a Leaking Bathtub Faucet

Figure A: Faucet stem assemble and replacement parts

Fig. A shows the bathtub plumbing faucet stem replacement parts and how to prepare the stem for reinstallation. Lubricate the parts with special plumber’s grease. If you’re working on a two-handled faucet, we recommend replacing the washers and seats in both the hot and cold valves.

First, unscrew the packing nut. Twist the stem clockwise and back it out of the bonnet. Pry out the old packing washer with a small flat-blade screwdriver or pick. Grease the stem threads and reinstall the stem in the bonnet. Grease the new packing washer and slide it in place, and then grease the packing nut threads and firmly tighten the packing nut. Use special plumber’s grease.

Second, remove the old seat washer screw and the old seat washer. Grease the new seat washer and the threads of the new screw and then reinstall them.

Third, pull off the old bonnet washer, grease the new one and slide it in place.

Fourth, apply pipe joint compound to the bonnet threads and reinstall it in the faucet body (Photo 4).

Five, grease the handle splines and replace the escutcheon and handle.

Required Tools for this bathtub faucet repair Project

Have the necessary tools for this how to fix a leaky bathtub faucet DIY project lined up before you start—you’ll save time and frustration. Adjustable wrenchHandle pullerUtility knife Bath socket wrench,
Seat wrench

Required Materials for this bathtub faucet repair Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list. Plumber’s greaseStem valve repair parts

Read more: familyhandyman.com

What's Your Reaction?

Cry Cry
0
Cry
Cute Cute
0
Cute
Damn Damn
0
Damn
Dislike Dislike
0
Dislike
Like Like
0
Like
Lol Lol
0
Lol
Love Love
0
Love
Win Win
0
Win
WTF WTF
0
WTF

Comments 0

Your email address will not be published. Required fields are marked *

How to Fix a Leaking Bathtub Faucet

log in

Become a part of our community!

Captcha!
Don't have an account?
sign up

reset password

Back to
log in

sign up

Join BoomBox Community

Captcha!
Back to
log in
Choose A Format
Personality quiz
Trivia quiz
Poll
Story
List
Open List
Ranked List
Meme
Video
Audio
Image